Medidor de tracción PCE-UTU 20
- Code / Model:
- Manufacturer: PCE Instruments
- Department:
- Category of products:
- Sub-category: Instruments and equipment
- You've seen it before.: 1
Note:This is just one example of the configuration of the PCE-UTU 20. Depending on your application you may need some additional special fixing device. Please contact us before placing an order for advice. We will set the configuration to suit your needs. Please note that you must add the installation
The vehicle shall be equipped with a traction meter PCE-UTU 20
Traction meter for traction test / drawing of tension-deformation diagram / different versions / Regulated DC motor / breakdown detection / variable test speed / force control / complex configuration options
Traction meter for traction test / drawing of tension-deformation diagram / different versions / Regulated DC motor / breakdown detection / variable test speed / force control / complex configuration options
The traction meter is suitable as a traction test device, so a standard standardised traction meter is used to determine material characteristics such as the determination of the elasticity limit, traction resistance, breakage lengthening and other characteristics by applying the traction meter.
As already mentioned above, the traction test is a standardized and destructive procedure, used for the examination of materials, for which standardized samples with the cross-sectional surface defined by the application of extended force and fracture are used.
The traction meter provides the possibility to determine the elasticity limit, traction resistance and breakage length of the traction sample among others. After measurement the traction meter sends the detailed results, which are transferred to the software as a tension-deformation diagram.
- Measurement range: 0,4 ... 20 kN
- Precision class: 0.5
- Different versions
- Regulated DC motor
- Precision class: 0.5
- Different versions
- Regulated DC motor
- Variable test speed
- Covered housing components of
Dust paint
- Break detection
- Memory of maximum value
- Covered housing components of
Dust paint
- Break detection
- Memory of maximum value
| General technical specifications | |
| The vehicle shall be equipped with a traction meter PCE-UTU 20 | |
| Rated load | 20 kN |
| Precision classes | The following information is provided: |
| Traction | Controlled DC motor |
| Test speed | The following information is provided for the purpose of this Regulation: |
| Movement | Increased |
| Standard career | 1000 mm (without a fastening device and fastening adaptor) |
| Workplace | Other, of a thickness of not more than 150 mm |
| Food | The following conditions shall apply: |
| Structure of the | 2 polished guide columns 2 ball spindles Column covering with a fuelle closure End switch for route limitation Powder coated housing components The colour: RAL 7035 |
| Security installation | Other, of a width of not more than 30 mm Security contact |
| Dimension | Other, of a width of not more than 30 mm |
| Weight | Approximately 155 kg |
| And thenGeneral technical specifications of the force sensor for UPM | |
| Installed under the mobile cross-section for compression and traction forces. Includes fastening material, socket, power outlet and wiring. | |
| Measurement range | 400 ... 20000 N |
| The nominal characteristic value | The following conditions shall apply: |
| Relative deviation from the characteristic value | Other, not further worked than hot-rolled |
| Relative deviation from linearity | Other, not further worked than hot-rolled |
| Relative slip error | ≤ ±0,03 % after 30 min. ≤ ±0,07 % after 8 h |
| The Commission shall adopt a decision on the | The following information is provided in the following table: |
| Overload | 50% |
| Type of protection | The following information is provided: |
| The following table summarizes the results of the evaluation: | The following definitions shall apply: automatic sensing of the sensor |
| Technical specifications of the electronic control and evaluation system | |
| Measurement data collection | 1 kHz |
| Screen | LCD screen |
| Interface | Other, of a kind used for the manufacture of goods |
| Functions | The force adjustment Regulation of movement Manual positioning Execution of a scheduled sequence Specifications for the speed of the crossover Back to the starting position Cycles Specification of the limit value for force/displacement/time Restoring the force/displacement indicator to 0 Adjustable regulatory factor Detection of breakage Record of maximum value with 2nd force sensors: choice of work area |
| Smart measuring and regulatory electronics | |
| Other machinery | 32 bit RISC architecture |
| Control lock | Other, of a kind used for the manufacture of goods |
| The following table summarizes the results of the evaluation: | Automatic detection of the sensor The following information is provided for in Part A of Annex I to this Regulation: |
| Interface | Other electrical equipment |
| A/D transducer | 2 x 24 bit A/D for DMS sensor Sampling rate: > 50 kHz 2 x 10 bit A/D for additional signal processing Sampling rate: > 50 kHz 1 x incremental signal input for measuring distance and angle |
| Software | |
| Functions | - Tools for the free programming of the verification sequences - Tools for the free programming of Calculations - Free setup of a time chart Real with overlapping multiple axes, scale Free and manual analysis function - Free configuration of the report format with inclusion of image files - Individual registration or ordering or export The Commission has also adopted a number of proposals for the Gross measurement calculations and values - Integrated user management - Automated - Suitable for nets - Multilingual - License per machine, multiworkplace |
| Basic configuration for material testing | 1 x Template for traction tests 1 x Template for compression tests, Curvature or alternative loads 1 x Template for traction and compression mooring tests |
