Acelerómetro PCE-VM 20
- Code / Model:
- Manufacturer: PCE Instruments
- Department: Test and measurement
- Category of products: Manufacture from materials of any heading
- Sub-category: Spectrum analyzers
- You've seen it before.: 1
Accelerometer for measuring vibrations in machines
Direct measurement according to DIN ISO 10816 / Different measurement modes /
Real-time FFT analysis / Configuration file for customized measurements
Direct measurement according to DIN ISO 10816 / Different measurement modes /
Real-time FFT analysis / Configuration file for customized measurements
The accelerometer is a compact device for the direct assessment of a machine's vibrational behavior. The device measures several vibration parameters: acceleration, speed and displacement. Thanks to integrated real-time FFT analysis it is possible to analyze and determine the state of a machine while
The accelerometer allows the analysis and visualization of the signals of piezoelectric vibration sensors according to the IEPE standard, as well as of piezoelectric vibration sensors with loaded output.
The accelerometer allows the analysis and visualization of the signals of piezoelectric vibration sensors according to the IEPE standard, as well as of piezoelectric vibration sensors with loaded output.
- Real-time FFT analysis
- A sturdy shell
- Different vibration parameters
- Direct valuation according to DIN ISO 10816
- Integrates a LiPo (lithium polymer) accumulator
- A sturdy shell
- Different vibration parameters
- Direct valuation according to DIN ISO 10816
- Integrates a LiPo (lithium polymer) accumulator
| Acceleration | 0 ... 200 m/s2, RMS and Peak-Peak |
| Speed | 0 ... 200 mm/s, RMS |
| Movement | 0 ... 2000 μm, Peak-Peak |
| Vibration accuracy | ± 5% |
| Magnitudes | Frequency |
| Acceleration | |
| Speed | |
| Movement | |
| FFT spectrum | |
| Units | Metric, imperial |
| The following is the list of the products covered by this Regulation: | |
| Interface | Other electrical equipment |
| Memory | Micro SD card of 4 GB |
| Operating time of the accumulator | Up to 8 hours in continuous operation |
| Type of accumulator | Lithium polymer |
| Screen | Color LCD of 128 x 160 pixels |
| Environmental conditions | -10 ... +55 °C |
| ≤ 80% H.r. without condensation | |
| Dimension | 132 x 70 x 33 mm |
| Weight | Approximately 150 g |
| Hand equipment: Not exposed to strong vibrations, magnetic fields, corrosive media or dust | |
| Technical specifications of the vibration sensor | |
| Sensitivity | The following conditions shall apply: |
| The frequency behaviour (±3 dB) | 0,5% or more |
| Frequency behaviour (± 10%) | The frequency of the sound is not less than 2 Hz. |
| Dynamic range | ±50 g, peak |
| Food and feed (IEPE) | 18 ... 30 V DC |
| Electrical power supplies | 2 ... 10 mA |
| Spectral noise at 10 Hz | Other, of a kind used for the manufacture of goods |
| Spectral noise at 100 Hz | The following is the list of the products used: |
| Spectral noise at 1000 Hz | Other, of a kind used for the manufacture of goods |
| The following shall be added: | Other, of a kind used for the manufacture of goods |
| The power output of the device shall be the same as that of the vehicle. | 10 ... 14 V DC |
| Carcass isolation | Other, of a kind used for the manufacture of goods |
| Environmental conditions | -50 ... +121 °C |
| Maximum impact protection | 5000 g, peak |
| Resonance frequency | 23000 Hz |
| Other, of a kind used for the manufacture of goods | Other, of a thickness of not more than 0,01 mm |
| Connection | 2 Pin MIL-C-5015 |
| Type of protection | Other, not further worked than hot-rolled |
| Weight | 90 g |
